変更履歴

realtek: Trap all frames with switch as destination to CPU-port

This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.

Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
 (commit: 98bb26f)

ramips: add support for Cudy X6

Specifications:

SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:

Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download

Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
 (commit: 4a8eaa5)

kernel: bump 5.15 to 5.15.36

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
 (commit: c3569a7)

kernel: bump 5.15 to 5.15.37

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
 (commit: 634a45c)

kernel: bump 5.15 to 5.15.38

Deleted (upstreamed):
mediatek/patches-5.15/120-10-v5.18-mtd-nand-fix-ecc-parameters-for-mt7622.patch [1]

Other patches automatically rebased.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.38&id=3ec920d755ae69c201b358e8d8e96c32f51145d8

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
 (commit: d9a063c)

realtek: do not reset SerDes on link change

Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.

A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.

The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.

The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[rewrite commit message based on discussion]
Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html
Signed-off-by: Sander Vanheule <sander@svanheule.net>
 (commit: d1b8246)

image: drop unused 'BuildKernel/MkFIT'

The 'MkFIT' recipe is no longer used across whole codebase.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
 (commit: 20ca59c)

ramips: fix booting on Samknows SK-WB8

This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
 (commit: 064e7e5)

lantiq: xway: disable unused switch drivers

None of the devices supported by target xway are using Realtek
RTL8366S, RTL8367A and RTL8367B switches. The switches mentioned
earlier were enabled when bumping the kernel version to 3.7 in
commit 3a948770cf46 ("add linux-v3.7").

Switches used by individual devices are listed below.

Device				Switch			PHY
Arcadyan ARV4510PW		Infineon ADM6996I	int. switch
Arcadyan ARV4519PW		Atheros AR8216		int. switch
Arcadyan ARV7506PW11		Realtek RTL8306G	int. switch
Arcadyan ARV7510PW22		Atheros AR8216		int. switch
Arcadyan ARV7518PW		Atheros AR8216		int. switch
Arcadyan ARV7519PW		Atheros RTL8306G	int. switch
Arcadyan ARV7525PW		N/A			IC+ IP101A
Arcadyan ARV752DPW		Realtek RTL8306G	int. switch
Arcadyan ARV752DPW22		Atheros AR8216		int. switch
Arcadyan ARV8539PW22		Atheros AR8216		int. switch
AVM Fritzbox 7312		int. SoC		Atheros AR8030-A
AVM Fritzbox 7320		int. SOC		Lantiq PEF7071V
AudioCodes MediaPack MP-252	Infineon ADM6996I	int. switch
BT Home Hub 2B			Infineon ADM6996I	int. switch
BT Home Hub 3A			Infineon PSB6972	Lantiq PEF7071V
Buffalo WBMR-HP-G300H-A		Atheros AR8316		int. switch
Buffalo WBMR-HP-G300H-B		Atheros AR8316		int. switch
Lantiq EASY50712		Infinein ADM6996I	int. switch
Netgear DGN3500			Realtek RTL8366RB	int. switch
Netgear DGN3500B		Realtek RTL8366RB	int. switch
Siemens	Gigaset sx76x		Infineon ADM6996I	int. switch
ZTE H201L			Realtek RTL8306G	int. switch
ZyXEL P-2601HN-F1		Realtek RTL8306E	int. switch
ZyXEL P-2601HN-F3		Realtek RTL8306E	int. switch

Reduces uncompressed kernel size by 36 kB.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(checkpatch.pl fixes)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 8b5d2a7)

bcm53xx: remove MR32's specific get_leds_dt code

the existing diag.sh code will pick up the LED
by itself. This is not/no longer needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 8f6e2bb)

apm821xx: use nested fixed-partitions

This makes it possible to fix Netgear WNDAP620+660 DTS ugliness.
Bring back the dtb and firmware partitions for the WNDR4700.
Thank you, mans0n.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: d65bafa)

ipq40xx: Lyra: update RGB LED-Controller node for 5.10+

Add the reg and color property to each channel node. This
update is to accommodate the multicolor framework.

Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>

Note:

There is only a single extremely bright RGB-LED.
The RGB-color channels (i.e.: blue-0, blue-1 and blue-2)
are running in parallel to increase the current delivery
beyond what a single PWM-output on the LED controller
could do.

BugLink: https://github.com/openwrt/openwrt/issues/9851
Reported-By: Thomas Bøge <thomas@boegenielsen.dk>
Tested-By: Thomas Bøge <thomas@boegenielsen.dk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 834c9b3)

linux-firmware: Update to version 20220509

git log --pretty=oneline --abbrev-commit 20220411..20220509 (sorted)

amdgpu:
480d6c2 amdgpu: update dcn_3_1_6_dmcub firmware
b4994be amdgpu: update gc_10_3_7_rlc firmware
61eb408 amdgpu: update psp_13_0_8 firmware
fcf9d8c amdgpu: update yellow carp DMCUB firmware

ath10k:
73743b8 ath10k: QCA4019 hw1.0: update board-2.bin
6ad0930 ath10k: QCA6174 hw3.0: update board-2.bin
729bd7f ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00288-QCARMSWPZ-1
9fce09f ath10k: QCA9888 hw2.0: update board-2.bin
b155d85 ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00156
44b8aee ath10k: QCA9984 hw1.0: update board-2.bin
4ad3bd3 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00156
1962cba ath10k: QCA99X0 hw2.0: add board-2.bin

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 25b29b5)

linux-firmware: take linux-firmware.git's qca99x0 boardfile

Kalle Valo managed to add the qca9980's boardfile in the
upstream repository. Sourcing the file from his repository
is no longer needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 4ba7f6d)

ipq-wifi: drop upstreamed board-2.bin

The BDFs for the:
	Aruba AP-303
	ASUS RT-AC42U
	AVM FRITZ!Repeater 1200
	Buffalo WTR-M2133HP
	Cell C RTL30VW
	D-Link DAP-2610
	EnGenius EAP2200
	EnGenius EMD1
	EnGenius EMR3500
	EnGenius EMR5000
	EZVIZ CS-W3-WD1200G EUP
	Google Wifi
	Linksys MR8300 V1.0
	Luma WRTQ-329ACN
	MobiPromo CM520-79F
	NEC Platforms WG2600HP3
	Plasma Cloud PA1200 (updated version)
	Plasma Cloud PA2200
	ZTE MF286D

were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.

Furthermore the BDFs for the:
	8devices Habanero
	OpenMesh A62
	OpenMesh A42
	AVM FRITZ!Box 4040

have been updated.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 91fa482)

uboot-fritz4040: Add support for Toshiba NAND

From Andreas Böhler:

"Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC
in contrast to the Macronix NAND with 4 bit ECC.".

Uboot needs to know this in order to have a chance to load from
the NAND.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
 (commit: 057bac2)

mpc85xx: enable error reporting for RAM and PCIe

All Freescale processors used in this target are capable to detect error
and correction. [1] It can not be used as kernel module. [2] This is
helpful to report hardware errors.

It enables three kernel options:

- EDAC, which is a subsystem
- EDAC_LEGACY_SYSFS, it enables sysfq nodes
- MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240

EDAC is already enabled for following targets:
qoriq, octeon, octeontx and zynq.

[1] https://cateee.net/lkddb/web-lkddb/EDAC.html
[2] https://patchwork.ozlabs.org/patch/554908/

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
 (commit: bfc73f4)

libubox: update to the latest version

f2d6752901f2 blob: clear buf->head when freeing a buffer
45210ce14136 list.h: add container_of_safe macro
cfa372ff8aed blobmsg: implicitly reserve space for 0-terminator in string buf alloc
d2223ef9da71 blobmsg: work around false positive gcc -Warray-bounds warnings

Signed-off-by: Felix Fietkau <nbd@nbd.name>
 (commit: 3e300e7)

ath79: fix I2C on GL-AR300M devices

On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.

Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
 (commit: 57efdd6)

ipq40xx: revert Cell-C RTL30VW to legacy caldata extraction

This partially reverts
commit cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data").

After switching to nvmem RTL30VW, wifi was broken:

[   19.118319] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   19.118377] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.130285] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   19.159092] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[   19.238764] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[   19.238847] ath10k_ahb a000000.wifi: failed to fetch board file: -12
[   19.247362] ath10k_ahb a000000.wifi: could not probe fw (-12)
[   20.190797] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   20.190853] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   20.202893] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   20.231357] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[   20.317318] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[   20.317399] ath10k_ahb a800000.wifi: failed to fetch board file: -12
[   20.326098] ath10k_ahb a800000.wifi: could not probe fw (-12)

Bootloader mangles in NAND partitions and removes precal@X nodes in
working system:

root@OpenWrt:~# echo $(cat /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/label)
0:ART
root@OpenWrt:~# ls /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/
label  name   reg

Revert to legacy method fixed the problem.

Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
 (commit: af425e4)

ath79: ZTE MF286[A,R]: add "Power button blocker" GPIO switch

ZTE MF286A and MF286R feature a "power switch override" GPIO in stock
firmware as means to prevent power interruption during firmware update,
especially when used with internal battery.
To ensure that this GPIO is
properly driven as in stock firmware, configure it with userspace GPIO
switch.

It was observed that on some units, the modem would not be
restarted together with the board itself on reboot, this should help
with that as well.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
 (commit: 1fabeeb)

util-linux: update to 2.38

Various fixes.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
 (commit: d93aae1)

util-linux: use meson to build

Compiles faster, is PIC by default, and does not have pkgconfig files
with wrong paths.

Add various fixes to it as it seems cross compilation was never tested.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
 (commit: 28cec43)

openssl: bump to 1.1.1o

This release comes with a security fix related to c_rehash.  OpenWrt
does not ship or use it, so it was not affected by the bug.

There is a fix for a possible crash in ERR_load_strings() when
configured with no-err, which OpenWrt does by default.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
 (commit: 7a5ddc0)

kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flash

The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
 (commit: 0bc794a)

IPQ4019: AVM FRITZ!Box 7530: Remove NAND ECC restrictions from DTS

Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
 (commit: f167f4a)

wolfssl: bump to v5.3.0-stable

This is mostly a bug fix release, including two that were already
patched here:
- 300-fix-SSL_get_verify_result-regression.patch
- 400-wolfcrypt-src-port-devcrypto-devcrypto_aes.c-remove-.patch

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
 (commit: 73c1fe2)

ramips: add led_source for Asus RT-AC1200 devices

this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.

The dts-binding is introduced in commit:
65dc9e0980255b15402c45b840f239b85be59b3d

Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
 (commit: 771ea6f)

ramips: Add support for SERCOMM NA502S

The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.

Note: BLE and audio are currently unsupported.

Specifications
--------------

  - MT7621ST 880MHz, Single-Core, Dual-Thread
  - MT7603EN 2.4GHz WiFi
  - MT7662EN 5GHz WiFi + BLE
  - 128MiB NAND
  - 256MiB DDR3 RAM
  - SD3503 ZWave Controller
  - EM357 Zigbee Coordinator
  - Telit UMTS module
  - Rechargeable battery
  - speaker and microphone

MAC address assignment
----------------------

LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.

Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.

Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.

If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with

mtd unlock ubi
mtd erase ubi

This should only be needed once.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
 (commit: 9ee6ac0)

kernel: bump 5.10 to 5.10.114

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
 (commit: 8592df6)

kernel: bump 5.10 to 5.10.115

Removed upstreamed:
  backport-5.10/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch
  pending-5.10/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
 (commit: b754b0c)

kernel: bump 5.15 to 5.15.39

Removed upstreamed:
  backport-5.15/850-v5.17-0001-PCI-pci-bridge-emul-Add-description-for-class_revisi.patch
  backport-5.15/850-v5.17-0002-PCI-pci-bridge-emul-Add-definitions-for-missing-capa.patch
  backport-5.15/850-v5.17-0003-PCI-aardvark-Add-support-for-DEVCAP2-DEVCTL2-LNKCAP2.patch
  backport-5.15/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch
  backport-5.15/850-v5.17-0005-PCI-aardvark-Comment-actions-in-driver-remove-method.patch
  backport-5.15/850-v5.17-0006-PCI-aardvark-Disable-bus-mastering-when-unbinding-dr.patch
  backport-5.15/850-v5.17-0007-PCI-aardvark-Mask-all-interrupts-when-unbinding-driv.patch
  backport-5.15/850-v5.17-0008-PCI-aardvark-Fix-memory-leak-in-driver-unbind.patch
  backport-5.15/850-v5.17-0009-PCI-aardvark-Assert-PERST-when-unbinding-driver.patch
  backport-5.15/850-v5.17-0010-PCI-aardvark-Disable-link-training-when-unbinding-dr.patch
  backport-5.15/850-v5.17-0011-PCI-aardvark-Disable-common-PHY-when-unbinding-drive.patch
  pending-5.15/850-0001-PCI-aardvark-Replace-custom-PCIE_CORE_INT_-macros-wi.patch
  pending-5.15/850-0004-PCI-aardvark-Rewrite-IRQ-code-to-chained-IRQ-handler.patch
  pending-5.15/850-0005-PCI-aardvark-Check-return-value-of-generic_handle_do.patch
  pending-5.15/850-0006-PCI-aardvark-Make-MSI-irq_chip-structures-static-dri.patch
  pending-5.15/850-0007-PCI-aardvark-Make-msi_domain_info-structure-a-static.patch
  pending-5.15/850-0008-PCI-aardvark-Use-dev_fwnode-instead-of-of_node_to_fw.patch
  pending-5.15/850-0009-PCI-aardvark-Refactor-unmasking-summary-MSI-interrup.patch
  pending-5.15/850-0010-PCI-aardvark-Add-support-for-masking-MSI-interrupts.patch
  pending-5.15/850-0011-PCI-aardvark-Fix-setting-MSI-address.patc
  pending-5.15/850-0012-PCI-aardvark-Enable-MSI-X-support.patch
  pending-5.15/850-0013-PCI-aardvark-Add-support-for-ERR-interrupt-on-emulat.patch
  pending-5.15/850-0015-PCI-aardvark-Optimize-writing-PCI_EXP_RTCTL_PMEIE-an.patch
  pending-5.15/850-0016-PCI-aardvark-Add-support-for-PME-interrupts.patch
  pending-5.15/850-0017-PCI-aardvark-Fix-support-for-PME-requester-on-emulat.patch
  pending-5.15/850-0018-PCI-aardvark-Use-separate-INTA-interrupt-for-emulate.patch
  pending-5.15/850-0019-PCI-aardvark-Remove-irq_mask_ack-callback-for-INTx-i.patch
  pending-5.15/850-0020-PCI-aardvark-Don-t-mask-irq-when-mapping.patch
  pending-5.15/850-0021-PCI-aardvark-Drop-__maybe_unused-from-advk_pcie_disa.patch
  pending-5.15/850-0022-PCI-aardvark-Update-comment-about-link-going-down-af.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
 (commit: 6cdf974)

kernel: bump 5.15 to 5.15.40

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
 (commit: e156f1f)

kernel: Add missing devm_regulator_get_exclusive()

This backports a patch from Linux 5.10.116 to fix a compile problem
introduced in 5.10.114.

drivers/usb/phy/phy-generic.c could not find
devm_regulator_get_exclusive().

Fixes: 8592df67f40b ("kernel: bump 5.10 to 5.10.114")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
 (commit: 7400ada)

bcm27xx-userland: update to latest version

The latest version contains some fixes and additions.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
 (commit: 4bf3827)

bcm27xx-gpu-fw: update to latest version

Latest GPU FW contains multiple fixes and improvements.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
 (commit: bca05bd)

bcm27xx: add support for linux v5.15

Build system: x86_64
Build-tested: bcm2708, bcm2709, bcm2710, bcm2711
Run-tested: bcm2708/RPiB+, bcm2709/RPi3B, bcm2710/RPi3B, bcm2711/RPi4B

Signed-off-by: Marty Jones <mj8263788@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
 (commit: 20ea6ad)