This reverts commit de8a800ca9bda1171bfe17ee7653532465a8b596. Host build uses host includes instead of staging/hostpkg. This breaks the build in case of selinux host libs being older than version 3.3. Revert for now until better fix is found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: ae4069c)
This reverts commit 2da891e7357c83c54a30075fcddbb63eeca0af99. secilc 3.3 requires libsepol to be version 3.3 as well and doesn't build otherwise. Revert for now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: 19c5277)
Deselect CONFIG_VIDEO_SUN6I_CSI Kconfig symbol for now. If anyone wants to use CSI (camera interface) they should package the kernel module. After this change, sunxi targets build again.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: f5d071a)
During review of the MR32, Florian Fainelli pointed out that the SoC has a real I2C-controller. Furthermore, the connected pins (SDA and SCL) would line up perfectly for use. This patch swaps out the the bitbanged i2c-gpio with the real deal.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (commit: 6102f88)
The current rule produces empty trailers, causing the OEM firmware update application to reject our images.
The double expansion of a makefile variable does not work inside shell code. The second round is interpreted as a shell expansion, attempting to run the command ZYXEL_VERS instead of expanding the $(ZYXEL_VERS) makefile variable.
Fix by removing one level of variable indirection.
Commit 03e1d93e0779 ("realtek: add driver support for routing offload") added routing offload for IPv4, but broke IPv6 routing completely. The routing table is empty and cannot be updated:
root@gs1900-10hp:~# ip -6 route root@gs1900-10hp:~# ip -6 route add unreachable default RTNETLINK answers: Invalid argument
As a side effect, this breaks opkg on IPv4 only systems too, since uclient-fetch fails when there are no IPv6 routes:
root@gs1900-10hp:~# uclient-fetch http://192.168.99.1 Downloading 'http://192.168.99.1' Failed to send request: Operation not permitted
Fix by returning NOTIFY_DONE when offloading is unsupported, falling back to default behaviour.
Fixes: 03e1d93e0779 ("realtek: add driver support for routing offload") Signed-off-by: Bjørn Mork <bjorn@mork.no> (commit: d990f80)
dropbear: add config options for agent-forwarding support
* SSH agent forwarding might cause security issues, locally and on the jump machine (https://defn.io/2019/04/12/ssh-forwarding/). So allow to completely disabling it. * separate options for client and server * keep it enabled by default
Signed-off-by: Sven Roederer <devel-sven@geroedel.de> (commit: 5287def)
OpenWrt maintains two special out-of-tree DT properties: "qca,disable-5ghz" and "qca,disable-2ghz". These are implemented in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".
With the things being what they are, now might be a good point to switch the devices to the generic and upstream "ieee80211-freq-limit" property. This property is much broader and works differently. Instead of disabling the drivers logic which would add the affected band and channels. It now disables all channels which are not within the specified frequency range.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (commit: 4c8dd97)
ipq40xx: detangle ath10k-board-qca4019 from ath10k-firmware-qca4019*
Back in the day, the board-2.bin came with ath10k-firmware-qca4019. This changed with commit c3b2efaf24b5 ("linux-firmware: ath10k: add board firmware packages") which placed the board-2.bin into a separate package: ath10k-board-qca4019. This was great, because it addressed one of the caveat of the original ipq-wifi package: commit fa03d441e96e ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace | the board-2.bin. For this cases the user needs to | manually reinstall the wifi-board package once the | ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages no longer use "install-override" and the various QCA4019 variants list the ath10k-board-qca4019 as a CONFLICT package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (commit: fd717f5)
Remove 6rd tunnel delete workaround in as the real issue is now solved in netifd (https://git.openwrt.org/?p=project/netifd.git;a=commit;h=8f82742ca4f47f459284f3a07323d04da72ea5f6)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (commit: c4d2929)
Remove 6in4 tunnel delete workaround as the real issue is now solved in netifd (https://git.openwrt.org/?p=project/netifd.git;a=commit;h=8f82742ca4f47f459284f3a07323d04da72ea5f6)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (commit: 2d2c7c4)
ath10k: backport fix for module load regression with iram-recovery
Backport upstream fix for module load regression caused by IRAM recovery. Without this patch devices using mainline ath10k driver could lost wireless function because ath10k module failed to load.
Signed-off-by: Zhijun You <hujy652@gmail.com> (commit: e6a486f)
Specification: CPU: Allwinner H5, Quad-core Cortex-A53 DDR3 RAM: 512MB Network: 10/100/1000M Ethernet x 2 USB Host: Type-A x 1 MicroSD Slot x 1 MicroUSB: for power input Debug Serial Port: 3Pin pin-header LED: WAN, LAN, SYS KEY: Reset Power Supply: DC 5V/2A
Installation: Write the image to SD Card with dd.
Note: 1. OpenWrt currently does not support LED_FUNCTION, change back to the previous practice (Consistent with NanoPi R1). 2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to change the phy-mode from rgmii to rgmii-id. So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (commit: fde68cb)
build: move elecom-wrc-gs-factory to image-commands.mk
ELECOM WRC-X3200GST3 uses the same header/footer as WRC-GS/GST devices in ramips/mt7621 subtarget, so move "Build/elecom-wrc-gs-factory" to image-commands.mk to use from mediatek/mt7622 subtarget.
The only and important difference between v1 & v3 is in flash memory layout, so pls don't interchange these 2 builds!
Installation through web-ui (on OEM factory firmware): 1. Visit http://tplinkrepeater.net or the configured IP address of your RE305 v3 (default 192.168.0.254). 2. Log in with the password you've set during initial setup of the RE305 (there is no default password). 3. Go to Settings -> System Tools -> Firmware upgrade 4. Click Browse and select the OpenWRT image with factory.bin suffix (not sysupgrade.bin) 5. A window with a progress bar will appear. Wait until it completes. 6. The RE305 will reboot into OpenWRT and serve DHCP requests on the ethernet port. 7. Connect an RJ45 cable from the RE305 to your computer and access LuCI at http://192.168.1.1/ to configure (or use ssh).
Disassembly: Just unscrew 4 screws in the corners & take off the back cover. Serial is exposed to the right side of the main board (in the middle) and marked with TX/RX/3V3/GND, but the holes are filled with solder.
Installation through serial: 1. connect trough serial (1n8, baudrate=57600) 2. setup the TFTP server and connect it via ethernet (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc) 3. boot from a initramfs image first (choose 1 in the bootloader options) 4. test it a bit with that, then proceed to run sysupgrade build
MAC addresses as verified by OEM firmware:
use OpenWrt address reference LAN eth0 *:d2 label 2g wlan0 *:d1 label - 1 5g wlan1 *:d0 label - 2
The label MAC address can be found in config 0x2008.
Signed-off-by: Michal Kozuch <servitkar@gmail.com> [redistribute WLAN node properties between DTS/DTSI, remove compatible on DTSI, fix indent/wrapping, split out firmware-utils change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: c12ef2f)
Use nvmem framework for supported mac-address stored in nvmem cells and drop mac patch function for hotplug script for supported devices.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [rebase, move to correct node for d7800, include xr500] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: f44e933)
ipq806x: remove transition workarounds for qcom-smem partitions
The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switched to normalizing the partition names to lower case.
While both 5.4 and 5.10 were supported in the target, we carried a workaround to support both of them. Since the target has dropped 5.4 recently, those can be removed now.
![[Jenkins]](/jenkins/static/954a7549/images/svgs/logo.svg){kind=logo}
