ramips: replace pinctrl property names for ipTIME A1004ns
The pinctrl driver had been replaced with the upstream one in b756ea2a909a ("ramips: replace pinctrl property names"), but the initial A1004ns support patch did not reflect the changes. This commit updates its pinctrl property names.
Fixes: 9169482f640c ("ramips: add support for ipTIME A1004ns") Signed-off-by: Sungbo Eo <mans0n@gorani.run> (commit: 45e2b77)
ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1.
Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following:
ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. You need to powercycle the device afterwards to boot OpenWRT.
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: David Bauer <mail@david-bauer.net> (commit: 8d9c108)
kernel: netfilter.mk: fix kmod-ipt-nat6 installation on 5.4
xt_MASQUERADE.ko is picked up by both kmod-ipt-nat and kmod-ipt-nat6, causing conflict As kmod-ipt-nat6 already depends on kmod-ipt-nat, remove xt_MASQUERADE from it
Fixes: FS#2924 Fixes: 0fad8af85158 ("kernel: Include xt_MASQUERADE for kernel 5.2 and later") Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> (commit: 29a458b)
This can be rather confusing for contributors, since there are three layers in which they can be added. As for now there are none profiles other than generic (exception: geos) let's move them to these profiles. Being here this commit also removes packages in geode profiles already enabled in kernel config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (commit: 9c23ece)
x86: really remove packages already enabled in kconfig
This commit really removes packages in geode profiles already enabled in kernel config.
Fixes: 9c23ecee57 ("x86: move packages selection to profiles") Reported-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: be6543c)
84965b92f635 blockd: print symlink error code and string message 62c578c22f9d blockd: report "target" path as "mount" for autofs available mounts d1f1f2b38fa1 block: remove mount target file if it's a link 830441d790d6 blockd: remove symlink linkpath file if it's a dir or link c80f7002114f libfstools/mtd: attempt to read from OOB data if empty space is found
Signed-off-by: Felix Fietkau <nbd@nbd.name> (commit: b7d6e80)
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their DTS(I) files are incompatible to kernel 4.14.
Remove the corresponding kernel config files to signal that more boldly and to prevent accidentally patching the wrong kernel when pulling in older config patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 58bec0d)
kernel: fix include of myloader.o since kernel 5.4
Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Based on this, the selection of myloader.o in OpenWrt was also moved to that subdirectory, while the Kconfig and our local myloader.c file remained in /drivers/mtd.
This resulted in linking errors like the following (on ath25@5.4):
make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ... needed by 'drivers/mtd/parsers/built-in.a'. Stop. make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2 make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2
Since myloader.c is not too big, this patch moves it to the kernel patches, allowing to adjust the path for kernel 5.4 and keeping Makefiles and file paths better in sync.
Other patches have been refreshed accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 5f92349)
Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Like for myloader.c in the previous patch, this patch moves tplinkpart.c to the kernel patches, so the code and the kernel includes are at the same location and the path can be adjusted per kernel.
While at it, remove some outdated kernel version switches from the C code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: d3c9630)
This fixes a few minor issues (partially cosmetic) in ltq-adsl and ltq-adsl-fw Makefiles: - fix PKG_SOURCE_URL and switch to https - remove non-existant FW_NAME variable - fix package name for config inclusion - fix config symbol for debugging
Fixes: 1d0a9d0c0470 ("move ltq-adsl")
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: d8b3f53)
Commit 0543eb111081 ("imx6: 5.4: add missing kernel perf monitor symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which is exposed only when building perf, so add it back.
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch. This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus. SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding! This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com> (commit: 4c70bb4)
Before, only frames with a maximum size of 1528 bytes could be transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame, we typically need an MTU of at least 1532 bytes to be able to transmit without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656 bytes.
Tested with two ath10k devices in 802.11s mode, as well as with batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89 Link: https://github.com/greearb/ath10k-ct/commit/9e5ab25027e0971fa24ccf93373324c08c4e992d Cc: Ben Greear <greearb@candelatech.com> Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Signed-off-by: Sven Eckelmann <sven@narfation.org> (commit: 066ec97)
also change the download source to https and add a mirror drop merged patches
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> [Add extra changes to compile on FreeBSD, merge two patches] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (commit: 042917f)
kernel: backport fix for non-regular inodes on f2fs
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address for non-regular inode").
On 4.14, attempting to perform operations on a non-regular inode residing on an f2fs filesystem, such rm-ing a device node, would fail and lead to a warning / call trace in dmesg. This fix was already applied to other kernels upstream - including 4.19, from which the patch was taken.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com> (commit: ee50018)
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:
- apply alphabetic sorting in multiple files - use armada-3720 prefix for DTS like for other devices - fix vendor capitalization for model in DTSes - remove trivial comment in DTS files - use DEVICE_VENDOR/DEVICE_MODEL - remove redundant SUPPORTED_DEVICES - use SOC instead of DEVICE_DTS - remove empty line at EOF
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 3fdb086)
ramips: mt7621: use lzma-loader for D-Link DIR-860L B1
This device has trouble extracting big kernel from flash, and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary size limiting workaround.
Factory image sizes (commit: 5f126c541a74) with "CONFIG_ALL_KMODS=y": - original ("-d23", default): 4784188 bytes, LZMA ERROR 1 - with "-d19": 4915260, LZMA ERROR 1 - with "-d18": 4915260, diff to original: +128 KB - with "-d17": 4980796, diff to original: +192 KB - with this patch: 4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA compressed uImage.
The most robust solution would use a different loader, which reads the compressed kernel directly from the flash. See the thread at [0] for more details!
ramips: use lzma-loader for I-O DATA mt7621 devices
The official sysupgrade images for I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.) cannot be booted normally and the kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note: These devices use Z-LOADER to read the kernel from NAND flash and boot it. Z-LOADER cannot load and start plain lzma-loader, so additional lzma-compression is needed.
bef8f8a5966d mt76: mt7615: remove a stray if statement 89bd7199487f mt76: remove variable 'val' set but not used ee8ac234b84e mt76: mt7615: introduce mt7615_mcu_fill_msg 4999db4668f0 mt76: mt7615: introduce mt7615_mcu_wait_response 8ce6e40eba03 mt76: mt7615: cleanup fw queue just for mmio devices 9d1d2ee9add3 mt76: mt7615: introduce mt7615_init_device routine 7fbd2a57cea4 mt76: always init to 0 mcu messages 3b277cf18d95 mt76: mt7615: introduce mt7615_mcu_send_message routine 2a4132a55a4f mt76: mt7615: add mt7615_mcu_ops data structure 9ba71749a122 mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops 2e991f3e8cdd mt76: mt7615: move mt7615_mcu_set_sta in mt7615_mcu_ops 56852057cb90 mt76: mt7615: rely on skb API for mt7615_mcu_set_eeprom 642ecd978887 mt76: mt7615: rework mt7615_mcu_set_bss_info using skb APIs 2b0810af4a52 mt76: mt7615: move more mcu commands in mt7615_mcu_ops data structure 7a6285e63d88 mt76: mt7615: introduce MCU_FW_PREFIX for fw mcu commands e536b42ebc7d mt76: mt7615: introduce mt7615_register_map fccbdb628ffd mt76: mt7615: add mt7663e support to mt7615_reg_map d42244e9255c mt76: mt7615: add mt7663e support to mt7615_{driver,firmware}_own aebbe088127f mt76: mt7615: add mt7663e support to mt7615_mcu_set_eeprom 28e22d07f892 mt76: mt7615: introduce mt7615_eeprom_parse_hw_band_cap routine 167428592647 mt76: mt7615: introduce mt7615_init_mac_chain routine 23ca7acfc856 mt76: mt7615: introduce uni cmd command types c4171728cf70 mt76: mt7615: introduce set_bmc and st_sta for uni commands 9e5c76d2310a mt76: mt7615: add more uni mcu commands 779b2cebc147 mt76: mt7615: introduce set_ba uni command 21ee7da00f0a mt76: mt7615: get rid of sta_rec_wtbl data structure 2097f74f664c mt76: mt7615: introduce mt7663e support 8e9cd01228d0 mt7615: sync Kconfig with upstream 3b4f93840950 mt76: add memory barrier to DMA queue kick 8d301ace8ed7 mt76: mt7615: fix mt7663e firmware struct endianness 9bc1850ce711 mt76: mt7615: fix endianness in unified command a1b9b7d94aa0 mt76: mt7615: add missing declaration in mt7615.h 6e4b2a709fe7 mt76: sync Makefile with upstream 258dfb6afb30 mt76: mt76x02u: Add support for newer versions of the XBox One wifi adapter 9c3d84b62cc0 mt76: mt76x2u: introduce Mercury UD13 support ea8ea71933ca mt76: mt76x0: pci: add mt7610 PCI ID 9d555f82d329 mt76: mt7615: modify mt7615_ampdu_stat_read for each phy 8bd26d6c3172 mt76: mt7615: enable aggr_stats for both phy 1315afa511e0 mt76: mt7615: cleanup mib related defines and structs 072b50c61e0e mt76: mt7615: add more useful Tx mib counters b23ff3e9343a mt76: mt7663: fix mt7615_mac_cca_stats_reset routine 294abe47c9b2 mt76: mt7663: enable nf estimation d2d7bf2243f6 mt76: mt7615: make scs configurable per phy 908a2cfab88f mt76: mt7663: disable RDD commands eaef0a268b95 mt76: mt7615: add ethool support to mt7663 driver 96e07ef1113d mt76: mt7615: introduce mt7615_mcu_set_channel_domain mcu command 67182f36e3be mt76: mt7663: keep Rx filters as the default e6a3f3ffe53a mt76: mt7615: introduce hw scan support 12ecd5ba2146 mt76: mt7615: introduce scheduled scan support f6ab0bee3172 mt76: mt7615: introduce BSS absence event f208a9430044 mt76: mt7615: introduce rlm tlv in bss_info mcu command ea4f4d216dbe mt76: mt7615: remove unnecessary register operations 72c9380e70f9 mt76: add headroom and tailroom to mt76_mcu_ops data structure 63e14669e09d mt76: mt7615: introduce mt7663u support to mt7615_write_txwi 29d359ac7626 mt76: mt7615: introduce mt7615_mac_update_rate_desc routine 1f1dd2cb5b49 mt76: mt7615: introduce __mt7663_load_firmware routine cb6dcfd3cf13 mt76: mt7615: move mt7615_mac_wtbl_addr in mac.h d28e8e7ef912 mt76: mt76u: rely on mt7622 queue scheme for mt7663u f78cf8957aba mt76: mt7615: rework wtbl key configuration 2829497aaaf5 mt76: mt7615: introduce mt7615_wtbl_desc data structure 02c9ec4a15e7 mt76: mt7615: add address parameter to mt7615_eeprom_init e9c640c0a79e mt76: mt7663: correct the name of the rom patch 1e8b2fe5ab03 mt76: mt7615: do not always reset the dfs state setting the channel ec0ea46dacf9 mt76: mt7615: Delete an error message in mt7622_wmac_probe() d16a4698f1ac mt76: mt7615: disable merge of OTP ROM data by default 2b58998bb594 mt76: mt7615: add support for applying DC offset calibration from EEPROM 55198aafb756 mt76: mt7615: add support for applying tx DPD calibration from EEPROM 5a1eaa38d380 mt76: mt7603: disable merge of OTP ROM data by default bf60f43b12fb mt76: mt76x2: disable merge of OTP ROM data by default 9406eb1d110f mt76: mt7615: fix endian issues in applying flash calibration data 66d00b8c9dac mt76: mt7615: fix possible division by 0 in mt7615_mac_update_mib_stats 25d812dddcf8 mt76: mt7663: fix aggr range entry in debugfs 08b8bd2bc915 mt76: mt7615: disable hw/sched scan ops for non-offload firmware 8fb1cd20a776 mt76: mt7615: set hw scan limits only for firmware with offload support 05b23d7478fe mt76: mt7615: rework IRQ handling to prepare for MSI support b92c0d576769 mt76: mt7622: fix DMA unmap length 03daa60ca69c mt76: mt7663: fix DMA unmap length 5f2f676b1f01 mt76: mt7615: enable MSI by default 5822911f8026 mt76: remove unnecessary annotations a7035bce8517 mt76: mt7615: fix possible deadlock in mt7615_stop d4e6e225bc06 mt76: mt7615: move core shared code in mt7615-common module 94827d2033c7 mt76: mt7615: introduce mt7663u support 36591dd35f91 mt76: mt7615: enable scs for mt7663 driver bd80144cb5be mt76: mt7615: disable aspm by default 9dcb60b78ede mt76: mt7615: provide aid info to the mcu 6e443e89cce2 mt76: remove PS_NULLFUNC_STACK capability ea133325faa6 mt76: mt7663: introduce 802.11 PS support in sta mode ff3869b38cf2 mt76: mt7615: make Kconfig entry obvious for MT7663E 01fd34f3a6c5 mt76: mt7615: fix sta ampdu factor for VHT e5adbb2077e2 mt76: fix A-MPDU density handling d73e3a23a54e mt76: mt7615: use larger rx buffers if VHT is supported 257319e9b07d mt76: mt7615: never use an 802.11b CF-End rate on 5GHz 29a92c5606d6 mt76: mt7603: never use an 802.11b CF-End rate on 5GHz c0b19ac97c07 mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values 1656882f2723 mt76: mt7615: do not adjust MAC timings if the device is not running 4e7ce907faf3 mt76: mt7615: fix tx status rate index calculation 8304b3866100 mt76: mt7603: fix tx status rate index calculation 722d1f47d8ba mt76: add rx queues info to mt76 debugfs da329ef776b0 mt76: mt7615: parse mcu return code for unified commands facf74fd506f mt76: mt7615: fix mt7615_firmware_own for mt7663e e910787a9888 mt76: mt7615: fix max wtbl size for 7663 c9821f7d6a8c mt76: mt7615: fix mt7615_driver_own routine e35cc532c3d2 mt76: mt7615: fix aid configuration in mt7615_mcu_wtbl_generic_tlv b6cb91a71fe1 mt76: mt7615: rework mt7615_mac_sta_poll for usb code b193dd8100f8 mt76: mt7663u: enable AirTimeFairness 31cffa98920f mt76: mt7615: move mcu bss upload before creating the sta cde3716aa47e mt76: enable TDLS support 1846da5dd417 mt76: mt7615: set spatial extension index 6aaf0299730f mt76: mt7615: fix endian issues in dcoc/txdpd calibration 5de75b745cf9 mt76: mt7663: fix up BMC entry indicated to unicmd firmware a5f394c5ca48 mt76: mt7615: add sta pointer to mt7615_mcu_add_bss_info signature 1f2f3dda76b9 mt76: mt7615: fix event report in mt7615_mcu_bss_event c2a3cced36de mt76: mt76x0: enable MCS 8 and MCS9 1afabe78cfc5 mt76: mt7663: add the possibility to load firmware v2 5f3ccc722627 mt76: mt7663: remove check in mt7663_load_n9
Signed-off-by: Felix Fietkau <nbd@nbd.name> (commit: 1c008b6)
ramips: remove (kmod-)swconfig DEVICE_PACKAGES for Sitecom WL-351
These definitions are not required since swconfig is selected for the target anyway and kmod-swconfig is pulled as dependency by kmod-switch-rtl8366rb.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 40325ab)
ath79: add support for Ubiquiti PowerBeam 5AC Gen2
The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac 5 GHz bridge with a radio feed and a dish antenna. The device is hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.
Installation from stock airOS firmware: - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [changed device name in commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: e210fe9)
ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation AC
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC and Nanostation AC as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 80a094a)
Signed-off-by: Andre Heider <a.heider@gmail.com> [added test comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 1e3ee24)
For wave-2, there is now a new variant: htt-mgt-community (vs the old full-htt-mgt-community).
The non-full one (hence forth 'diet') compiles out a lot of firmware features that ath10k does not use. This saves a lot of resources and lets one configure more stations/vdevs/etc using fwcfg.
Backport patch from hostapd.git master that fixes copy/paste error in crypto_bignum_sub() in crypto_wolfssl.c.
This missing fix was discovered while testing SAE over a mesh interface.
With this fix applied and wolfssl >3.14.4 mesh+SAE works fine with wpad-mesh-wolfssl.
Cc: Sean Parkinson <sean@wolfssl.com> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: 4b3b8ec)
This patch removes support for swconfig and switches to dsa driver.
swconfig and switch drivers are removed. DSA driver is enabled and configuration is adjusted.
In kirkwood only two devices have switches: Linksys EA3500 and EA4500.
WAN MAC configuration in 02_network is required because otherwise WAN would have the same MAC address as lan interfaces. In swconfig solution the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled and wan is part of the switch, we have to set it manually.
Compile tested: EA3500, EA4500 Run tested: EA4500
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [minor commit title/message adjustments, remove swconfig package for devices] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (commit: 4fd7e53)
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19 support broken on the affected devices. Support on kernel 5.4 seems to have been running fine for almost 2 months on multiple devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Pawel Dembicki <paweldembicki@gmail.com> (commit: 0af2c44)
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19 support broken on the affected devices. Support on kernel 5.4 seems to have been running fine for almost 2 months on multiple devices, while support for 4.19 has never left testing state.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Pawel Dembicki <paweldembicki@gmail.com> (commit: 8b37389)
ath79: split Teltonika RUT955 to support other RUT9xx models
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and a part specific to that version of RUT955 already supported. Also harmonize GPIO and LED names with what is used by the vendor firmware and assign RS485 DTR signal.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: c8b309b)
This board was previously supported in ar71xx as 'RUT9XX'. The difference between that and the other RUT955 board already supported in ath79 is that instead of the SPI shift registers driving the LEDs and digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs, I2C support as well as support for PCA953x has to be built-in and cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344) - built-in 4G/3G module (example: Quectel EC-25EU) - internal microSD slot (spi-mmc, buggy and disabled for now) - RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0) - RS422/RS485 (AR934x high speed UART, /dev/ttyATH1) - analog 0-24V input (MCP3221) - various digital inputs and outputs incl. a relay - 11x LED (4 are driven by AR9344, 7 by PCA9539) - 2x miniSIM slot (can be swapped via GPIO) - 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS) - 1x button (reset) - DC jack for main power input (9-30 V) - debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org> (commit: aa4a33a)
dnsmasq: always inform about disabled dhcp service
Init script checks for an already active DHCP server on the interface and if such DHCP server is found, then it logs "refusing to start DHCP" message, starts dnsmasq without DHCP service unless `option force 1` is set and caches the DHCP server check result.
Each consecutive service start then uses this cached DHCP server check result, but doesn't provide log feedback about disabled DHCP service anymore.
So this patch ensures, that the log message about disabled DHCP service on particular interface is always provided.
Acked-by: Hans Dedecker <dedeckeh@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> (commit: b17a5a9)
Pulls in workaround for TX rate code firmware bug which might as well help track it down via different printk()s and thus possibly provide more clue for proper fix.
Firmware currently sends wrong (0xff) TX rate code which causes WARN_ONCE, so the workaround just changes this bogus value (0xff) into 0.
For 5.4 it also pulls in tx-queue-wake throttling patch "ath10k: Restart xmit queues below low-water mark", which should improve performance with high number of concurrent TCP streams.
Ref: https://github.com/greearb/ath10k-ct/pull/129 Signed-off-by: Petr Štetiar <ynezz@true.cz> (commit: 8036e7e)
Added generic config symbol `ARM64_ERRATUM_1542419` due to Fixes: f2791551cedb ("arm64: errata: Hide CTR_EL0.DIC on systems affected by Neoverse-N1 #1542419").
* compat: support latest suse 15.1 and 15.2 * compat: support RHEL 7.8's faulty siphash backport * compat: error out if bc is missing * compat: backport hsiphash_1u32 for tests
We now have improved support for RHEL 7.8, SUSE 15.[12], and Ubuntu 16.04.
* compat: include sch_generic.h header for skb_reset_tc
A fix for a compiler error on kernels with weird configs.
* compat: import latest fixes for ptr_ring * compat: don't assume READ_ONCE barriers on old kernels * compat: kvmalloc_array is not required anyway
ptr_ring.h from upstream was imported, with compat modifications, to our compat layer, to receive the latest fixes.
* compat: prefix icmp[v6]_ndo_send with __compat
Some distros that backported icmp[v6]_ndo_send still try to build the compat module in some corner case circumstances, resulting in errors. Work around this with the usual __compat games.
* compat: ip6_dst_lookup_flow was backported to 3.16.83 * compat: ip6_dst_lookup_flow was backported to 4.19.119
Greg and Ben backported the ip6_dst_lookup_flow patches to stable kernels, causing breaking in our compat module, which these changes fix.
* git: add gitattributes so tarball doesn't have gitignore files
Distros won't need to clean this up manually now.
* crypto: do not export symbols
These don't do anything and only increased file size.
* queueing: cleanup ptr_ring in error path of packet_queue_init
Sultan Alsawaf reported a memory leak on an error path.
* main: mark as in-tree
Now that we're upstream, there's no need to set the taint flag.
* receive: use tunnel helpers for decapsulating ECN markings
ECN markings are now decapsulated using RFC6040 instead of the old RFC3168.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> (commit: f57230c)
Flash instruction using U-Boot TFTP: 1. Connect the UART pin on WN-G300DGR (CN1, Vcc/GND/TX/RX from caret) with PC 2. Set PC to fixed ip address 192.168.99.8 3. Download lede-ramips-rt305x-wn-g300dgr-squashfs-sysupgrade.bin and rename it to uImageWN-G300DGR 4. Start a tftp server with the file uImageWN-G300DGR in its root directory 5. Turn off the router 6. Turn on router and repeatedly press "2" key on the UART console 7. When entering tftp mode, press keys "y", "Enter", "Enter", "Enter" 8. After a short time, the firmware should be transferred from the tftp server 9. Wait ~60 second to complete flash